Gas Hydrate Triaxial Testing System Wille Geotechnik
Liên hệ
Loading...
Gas Hydrate Triaxial Testing System Wille Geotechnik
American

American

Viet Nam

Viet Nam

Gas Hydrate Triaxial Testing System Wille Geotechnik

This Advanced Gas Hydrate Triaxial Test System specifically designed to perform triaxial tests on sediment samples containing methane hydrates under extreme conditions, including sub-freezing temperatures and high pressures.

A Gas Hydrate Triaxial Test System is a specialized laboratory setup designed to simulate and study the mechanical behavior of gas hydrates in soils, typically under varying pressure, temperature, and environmental conditions. Gas hydrates are crystalline structures formed from water and gas (like methane) under high pressure and low temperature, commonly found in deep-sea sediments or permafrost regions. These structures can impact soil stability and are of significant interest in fields like energy extraction, geotechnical engineering, and climate science.

The system has been significantly enhanced in pore pressure fluid management, including capabilities for mixing, flow direction control, and circulation, to accommodate a wide range of test scenarios. These include the formation of hydrates in partially water-saturated sediments, permeability measurements, gas injection into fully water-saturated sediments, and fluid circulation through fully water-saturated samples.

  • Static loads in different ranges up to 250kN
  • Electromechanical loading system to cover all required loads
  • Different sample sizes up to 100mm
  • Different cell pressures up to 50MPa
  • Frozen Soil test up to -20 °C degree
  • High Temperature test up to +70 °C
  • Software including different test modules e.g. Standard Static triaxial tests (CD, CU and UU), Stress path tests, dynamic tests and etc.

Static axial load

Up to 250 kN

Confining pressure

Up to 50 MPa

Temperature range

-10 up to +60 °C

Sample size

Up to 100 mm diameter

Wille Geotechnik Gas Hydrate Triaxial SystemGas Hydrate Triaxial Test Equipment Wille GeotechnikWille Geotechnik Hydrate Triaxial ApparatusTriaxial Testing System for Gas Hydrates Wille Geotechnik
  • Chia sẻ qua viber bài: Gas Hydrate Triaxial Testing System Wille Geotechnik
  • Chia sẻ qua reddit bài:Gas Hydrate Triaxial Testing System Wille Geotechnik

PRODUCTS

Loading...

RELATED PRODUCTS

Large Diameter Dynamic Triaxial Testing System Wille Geotechnik

The large-scale triaxial testing systems are customized construction systems configured based on the testing requirements of the customer. These systems are used to perform static tests on specimens with large particle sizes, such as dam ballast, railway ballast, and gravels. The Large Diameter Dynamic Triaxial Testing System can apply up to 1000 kN load with a frequency of up to 50 Hz  on samples with a diameter of up to 600 mm. (An ultra-large triaxial system is available on request for sample sizes up to 1000 mm.) The wide column spacing enables the accommodation of large cells, even with environmental chambers and furnaces. The load frame features a pneumatic sliding system, which allows easy movement of the triaxial cell out of the loading area, making test setup handling easier for the operator. The powerful multifunctional GEOsys software supports all test procedures, providing easy access to all testing sessions.
Xem thêm

Resilient Modulus Testing System Wille Geotechnik

The new fully automatic Resilient Modulus Testing System (RMTS) is based on our cyclic tabletop electromechanical Triaxial test System with closed-loop control of the axial load, displacement and confining pressure. The Cyclic load simulates conditions produced by traffic. The device with different components can comply with the requirements of AASHTO T 307-99, AG:PT/T053 and AS1289.6.8.1. As the device is based on our cyclic Triaxial test therefore can also be used to perform other dynamic and static tests such as Stress Path, cyclic strength, liquefaction, Ko- Consolidation, as well as conventional UU, CU, and CD tests with the addition of components for back pressure control and pore pressure measurement. GEOsys software in combination with this unit performs all your tests automatically and without operator assistance during the test period.
Xem thêm

Servo Hydraulic Dynamic Triaxial Testing System Wille Geotechnik

This series of Dynamic Triaxial test systems gives the possibility to perform large loads and frequencies on the required specimen size in combination of static or cyclic cell pressure. The Wide column spacing enables to accommodate large cells even with environmental chambers and furnaces. The Triaxial system can generate and apply different types of loading waveforms that can be given to the sample e.g. Sinusoidal, Square, Triangular, Rectangle, Ramp signal, and user-defined waveform. The dynamic servo hydraulic load frame has different models which could be selected per as required technical test specification of the user e.g: 1) Table top model 2) Floor type model 3) Twin type model (independent dynamic - static actuators)
Xem thêm

Columnless Cyclic Triaxial Testing System Wille Geotechnik

The column-less loading system applies the static and cyclic loads from the bottom of the Triaxial cell. The top of the cell is free operating space to facilitate installation of sample or local strain measuring devices. The Triaxial cell is connected to a lifting mechanism that lifts the cell wall up and gives the easiest way for the operator to handle the cell. The load piston has the possibility to compensate for cell pressure changes effected by the volume change of the piston inside the triaxial cell during cyclic and static tests. This loading system is specially designed and configured for cyclic Triaxial tests and use compensated ram technology. The system includes a special load pistol construction to compensate cell-pressure changes affected by the volume change of the movement of piston in and out of the triaxial cell.
Xem thêm